136L Convection Drying Oven with Digital Temperature Controller (22"x22"x18", 250C Max) - EQ-DHG-9140A

EQ-DHG-9140A is a CE Certified  Convection Oven with a digital temperature controller. It can achieve dependable, uniform conditions by converting heat to the sample evenly. Such convection oven can be widely used for drying, storing, wax-melting and sterilization. It is a piece of ideal heating equipment for material R&D laboratories. (Replace EQ-DHG-9140V220 with larger capacity and temperature controller on the left side since Sep. 20, 2018) SPECIFICATIONS:

Working Voltage	208-240VAC, Single Phase, 50/60 Hz (20A Breaker Required)
Max. Power Consumption	2300W
Max. Operating Temperature	250°C continuous Heating by blow hot air
Max. Heating Rate	10°C/min
Temperature Stability	< ±1.0°C
Chamber	Interior Material: Stainless Steel Dimensions: 450 L x 550W  x 550H，mm   （~ 21.6"L x 21.6" H  x 17.7 "D ） Volume: 136 L
Temperature Controller	Precision digital temperature controller with +/- 1°C accuracy
Sensor	Overheat protection sensor automatically cuts power if over-heated
Shelves	2 stainless steel shelves were included for immediate use
Product Dimensions	830 L x 580 W x 695 H, mm
Compliance	CE Certified.  NRTL / CSA certification is available upon request at the extra cost.
Warranty	One Year limited warranty with lifetime support (except for consumable O-rings)
Operation Video
Application Notes	For accurate temperature recording, you shall calibrate the temperature by Temperature Calibrating Kit by yourselves, and set temperature offset in the controller Please click here to learn How to Calibrate the oven temperature and set temperature offset
Shipping Weight	260 lbs
Shipping Dimensions	48"(L) x 40"(W) x 45"(H)

Power	Single Phase 208~240 VAC 50/60 Hz. 2600 W with 20A breaker required
Structure	The chamber is structured with stainless steel and welded to bracing pieces. Two racks of SS304 heating plate inside the vacuum chamber, which directly heat heats the chamber Warning: never directly put samples on the heating plate, please use a ceramic sheet or stainless tray to contain sample Chamber material: 1Cr18Ni9Ti stainless steel Chamber size：  18x18x18", （ 91 Liter,  3.4 Cubic Feet ）
Temperature Control	Two programming temperature controls are equipped for discrete control on each heater 30 segments programmable with ± 1ºC accuracy Continuous working temperature:  50 - 500 ºC Max. working temperature:  550 ºC f < 2 hours The maximum temperature difference between the two zones:  100ºC. Temperature Uniformity: ±5°C in 12x12x12" chamber center zone. The software and PC interface module is available at extra cost.
Vacuum Pump & Floating-Meter	Dual-stage vacuum pump with exhaust filter installed on the bottom. Maximum vacuum: <133pa or 2 Torr Built-in mechanical vacuum gauge One 1000 mL/min gas flowmeter for monitoring gas gauge, fill, and flow. One Rotary Vane Vacuum Pump with Exhaust Filter, Bellows & KF-D25 Inlet is included
Water Cooling	One Digital controlled Recirculating Water Chiller EQ-KJ5000 is included. (click Pic. left to see details) Refrigeration range: 5~35°C Flowing range: 16L/minute Coolant tank capacity: 6 Liter Use anti-corrosion coolant for the best performance.
Warranty	One-year limit warranty and lifetime support
Certificate	CE Certification NRTL or CSA Certification is available upon request at extra cost.
Product Dimensions	610 x 690 x 1350 mm (24" x 27" x 53")
Shipping Weight & Dimensions	610 lbs 48"x40"x65"
Operation Manual
Application Notes	For accurate temperature measurement, you may do calibration by using the temperature calibrating kit.  For more information on how to calibrate the oven temperature, please read the document How to calibrate the oven.
Attention	After heating the oven to high temperature, the chamber will be dulled and discolored. They are normal phenomena and will not affect the performance of the oven. All sample inside the chamber should not have any contact with the chamber wall.