Phone

(+65) 6284 3818

Email

sales@premier-sols.com

Enquriy
Automatic Winder for The Assembling of Multi Cylindrical Cell at 10 PPM Speed for 200 Cell/Batch - MSK-112A-SA

Automatic Winder for The Assembling of Multi Cylindrical Cell at 10 PPM Speed for 200 Cell/Batch - MSK-112A-SA

0.0/5 rating (0 votes)

Description

MSK-112A-SA is a fully automatic winding machine for assembling muti-cylindrical cell cores (also known as “jelly roll”) at 10 PPM ( 10 pack per minute).  The batch of cathode and anode strips ( pre-welded tab),  roll of separator and roll of tape are pre-installed in the machine, then you can touch button to wind the core of cylindrical cell automatically at 10 PPM speed up to 200 cell per batch

 

SPECIFICATIONS:

Features
  • Color touchscreen control
  • Pre-loading one batch electrodes, one roll of separator, and one roll of tape, then touch button to go
  • Automatic finish cut and tape upon the completion of the configured number of rotations
  • 10 pcs per minute speed for each batch up to 200 cells.
  • Optional for 18650, 21700 or 26650 cell
Input Power
  • Single phase 208 - 240 VAC, 50 / 60 Hz
  • 2 000 W power
Compressed Air

  • Compressed air of 0.7 MPa is needed for the operation of this machine
  • Please note the air compressor is not included. Please click the picture below to order one at MTI, or order it from your local hardware store
  • Attention: If a gas cylinder is used instead of air compressor(pic2), a two-stage pressure regulator(pic1) must be installed on the gas cylinder to limit the pressure within the required working range for safe operation. Click here to learn the installation of a gas regulator.
      pic1                pic2
Cathode / Anode Feeding
  • Pre-loading one batch of electrodes ( 100 trip max.), one roll of separator, and one roll of tape,
  • Vaccum holder will absorb the electrode strip in one by one to feed into assembling line
  • Width range: 25 – 70 mm (adjustable on feeder bed)
  • Thickness range: 100 – 300 μm
Separator Feeding
  • Loading material: separator film rolls, such as polyethylene (PE) or polypropylene (PP)
  • Length range: separator roll with a diameter < 250 mm
  • Width range: 25 – 70 mm
  • Thickness range: < 100 μm
  • Tension range: 0 – 4 N for both top and bottom separator films
Winding
  • Winding needle size: 3.5 mm OD
  • Electrode winding size: 14 – 32 mm OD, 25 – 70 mm in length
  • To wind an electrode core with a certain OD, a spreadsheet for calculating needed number of turns and electrode sheet length can be downloaded here
  • Winding speed: 0 – 400 rpm adjustable
  • Winding precision: < 0.5 mm edge roughness
Tape  Loading
  • One roll of tape pre-load on the machine for strapping finished electrode core with the  tapes
  • Roll diameter:   150 mm Max.
  • When winding finished, the tape will be applied to the winded core and cut.
Size
  • 1600 mm L x 1300 mm W x 600 mm H
Net Weight
  • 800 kg
Warranty
  • One-year limited warranty on lifetime support
  • Rusting or damage due to improper storage conditions or maintenance is not covered by warranty
Compliance
  • CE Certified
  • MET Certification is available upon request at extra cost
Operation Instruction & Video            
    
Optional

Share this product

Please type your full name.
Invalid Input
Invalid Input
Invalid Input
Invalid email address.
Invalid Input
Invalid Input
Invalid Input
Invalid Input

Register for new product information:    

Premier Solutions (PS) Pte Ltd Singapore

Please publish modules in offcanvas position.