Phone

(+65) 6284 3818

Email

sales@premier-sols.com

Enquriy
Single channel potentiostat galvanostat model CS310

Single channel potentiostat galvanostat model CS310

0.0/5 rating (0 votes)

Description

Specifications
Potential control range:±10V
Current control range:±2A
Potential control accuracy:0.1%×full range±1mV
Current control accuracy:0.1%×full range
Potential resolution:10μV (>100Hz),3μV (<10Hz)
Current sensitivity:1pA
Rise time:<1μS (<10mA), <10μS (<2A)
Reference electrode input impedance:1012Ω||20pF
Current range:2nA~2A, 10 ranges
Compliance voltage:±21V
Maximum current output:2.0A
CV and LSV scan rate :0.001mV~10,000V/s
CA and CC pulse width:0.0001~65,000s
Current increment during scan:1mA@1A/ms>
Potential increment during scan:
0.076mV@1V/ms>
SWV frequency:0.001~100 kHz
DPV and NPV pulse width:0.0001~1000s
AD data acquisition:
16bit@1 MHz,20bit@1 kHz
DA Resolution:16bit, setup time:1μs
Minimum potential increment in CV:0.075mV
IMP frequency:10μHz~1MHz
Low-pass filters:Covering 8-decade
Potential and current range:Automatic
Electrochemical impedance
Signal generator
Frequency range:10μHz~1MHz
AC amplitude:1mV~2500mV
DC Bias:-10~+10V
Output impedance:50Ω
Waveform:sine wave, triangular wave and square wave
Wave distortion:<1%
Scanning mode:Logarithmic/linear, increase/decrease
Signal analyzer
Integral time:
minimum:10ms or the longest time of a cycle
Maximum:106 cycles or 105s
Measurement delay:0~105s
DC offset compensation:
Potential automatic compensation range:-10V~+10V
Current compensation range:-1A~+1A
Bandwidth:8-decade frequency range, Automatic and manual setting
PC and O/S requirement
Communications Interface:isolated Universal Serial Bus (USB 2.0)
Operating System:Windows 2000/NT/XP/ win7/win8/win10
Weight / Measurements
Net weight:6.5kg
Instrument size:365 x 305 x160mm 

 

CS310 Potentiostat / Galvanostat contains a fast digital function generator, high-speed data acquisition circuitry, a potentiostat and a galvanostat. With high performance in stability and accuracy with advanced hardware and well-functioned software, it is a comprehensive research platform for corrosion, batteries, electrochemical analysis, sensor, life science and environmental chemistry etc.
It includes Electrochemical impedance spectroscopy(EIS) technique.

 

CS310 is a cost-effective model for researchers who will need EIS, CV, LSV, galvanostatic charge & discharge, OCP, polarization curve(Tafel) etc. It can be used for areas of corrosion, battery and many others. The difference between CS350 and CS310 is that CS350 includes more voltammetric methods, such as DPV, NPV, SWV, ACV, DNPV and voltammetry stripping techniques, which are not included inCS310. It can be updated to model CS350 if you have the need in the future.

 

Application

                    

(1)Reaction mechanism of Electrosynthesis, electrodeposition (electroplating), anodic oxidation, etc.
(2) Electrochemical analysis and sensor;
(3)Corrosion study of metals in water, concrete and soil etc;
(4) Fast evaluation of corrosion inhibitor, water stabilizer, coating and cathodic protection efficiency.
(5) New energy materials (Li-ion battery, solar cell, fuel cell, supercapacitors), advanced functional materials, photoelectronic materials;                                                                 

 

HARDWARE FEATURES
Potential control range: ±10V;
Compliance voltage: ±21V;
Current control range: ±2A;
Potential resolution: 10μV; current resolution 1pA
Built-in frequency response analyzer(FRA)
Frequency range: 10μHz~1MHz;
Dual-channel high-speed 16bit/high-accuracy 24bit AD converter;
High-bandwidth high input impedance amplifier unit
Built-in FPGA DDS digital signals synthesizer
High-power Potentiostat/Galvanostat/ZRA

 

SOFTWARE FEATURES
CS studio software provides users a versatile smoothing/ integration kit, which can complete the calculation of peak height, peak area and peak potential of CV curves.

CS studio also provides powerful non-linear fitting on Butler-Volmer equation of polarization curve. It can calculate Tafel slope, corrosion current density, limitation current, polarization resistance, corrosion rate. It can also calculate the power spectrum density, noise resistance and noise spectrum resistance based on the electrochemical noise measurements.

CS Studio software can achieve real time saving of the measuring data. The data can be automatically saved even in case of sudden power off.

CS studio kit has a built-in versatile timing policy for combined measurements, which can facilitate the automation of experiments and save time.

Battery analysis: charge & discharge efficiency, capacity, specific capacitance, charge & discharge energy etc.
EIS analysis: Bode, Nyquist, Mott-Schottky plot

  

 

TECHNICAL ADVANTAGES

1. Impedance (EIS)
CS310 potentiostat applies correlation integral algorithm and dual-channel over-sampling technique, and has strong anti-interference ability. It is suitable for EIS measurements of high-impedance system (>109Ω, such as coating, concrete etc.). It can also be used to obtain Mott-Schottky curve and differential capacitance curve. During test, the software can display real-time open circuit potential(OCP) without entering.

  
EIS of AA6063 Al alloy in Ce3+ containing 3% NaCl solution
Polarization curve of Ti-based amorphous alloy & stainless steel in 3%NaCl solution
 

2. Polarization curve
It can complete linear polarization curve and Tafel plot measurements. The user can set the anodic reversal current (passivation film breakdown current) of the cyclic polarization curve to determine material’s pitting potential and protection potential and evaluate the its susceptibility to intergranular corrosion. The software employs non-linear fitting to analyze polarization curve, and can make fast evaluation of material’s anti-corrosion ability and inhibitors.

 

3. Voltammetry
It can do the following electroanalysis methods: Linear Sweep Voltammetry(LSV), Cyclic Voltammetry(CV). It integrates calculation of peak area, peak current and standard curve analysis.

LSV curve: mesoporous carbon material in 0.1M KOH
CV curves of PPy supercapacitor in 0.5 mol/L H2SO4
 

 

 

 

4. Electrochemical Noise
With high-resistance follower and zero-resistance ammeter, it measures the natural potential/current fluctuations in corrosion system. It can be used to study pitting corrosion, galvanic corrosion, crevice corrosion, and stress corrosion cracking etc. Through noise spectrum, we can evaluate the inducement, growth and death of metastable pitting and crack. Based on calculation of noise resistance and pitting index, it can complete localized corrosion monitoring.

Electrochemical noise of low-carbon steel in 0.05mol/L Cl-+0.1mol/L NaHCO3
 

 

5. Full floating measurement
CS310 workstation uses full-floating working electrode. It can be used for autoclave electrochemical measurements, on-line corrosion monitoring of metallic components under the ground (rebar in concrete, etc.)

 

 

6. User-defined methods
CS310 workstation supports user-defined combination measurements. The user can set cyclic timing measurements of an electrochemical method or several methods. 

 

Standard supply list for potentiostat Model CS310
Instrument host CS310*1
CS studio software(Testing & data analysis)*1
Power cable*1
USB cable *1
Electrode cable *2
Dummy cell*1
**If you need electrodes and cells, please kindly contact us for purchase.

 

 

Service

1. Warranty period: 5 years
2. Provide installation guidance and manual, software installation video.
3. Lifetime free software upgrading and technical service
4. Provide repair service for free

Share this product

Enquiry Form

Please type your full name.
Invalid email address.
Invalid Input
Invalid Input

Register for new product information:    

Please publish modules in offcanvas position.